
How-to guide
Grout sealing
Seal the grout in your shower, bathroom or kitchen yourself, step by step. What matters most is the start: seal only grout that is clean and completely dry.
The short answer
Grout sealing soaks a clear penetrating sealer into cement grout to help it resist spills and dirt. Repair any cracks, scrub the grout clean and let it dry completely, which can take up to 24 hours. Seal the lines a small section at a time, wiping sealer off the tiles before it dries. Add a second coat, check that drops of water bead, then keep it dry for at least 24 hours.
What you need
- Clear penetrating grout sealer
- Grout cleaner or mild detergent
- Stiff grout brush
- Clean dry cloths
- Brush-on or spray applicator
- Protective gear from the label
How to seal grout, step by step
For cement grout on walls, floors and in showers.
- Check the grout type and any old sealerCement grout is porous, so unsealed grout takes in water and stains sooner. Epoxy grout does not need sealing. Put a few drops of water on old grout and wipe them off after 5 minutes: if they soaked in or left it darker, it is not sealed. Repair cracked or missing grout and strip any peeling sealer first.
- Scrub the grout cleanScrub the lines with a tile and grout cleaner, or water and a mild detergent, and a stiff brush. Treat any mould with a product made for it, following the label. Wipe off the residue with a damp cloth, as sealer locks in any dirt left behind.
- Let the grout dry completelyAllow up to 24 hours, or 24 to 48 hours in humid weather or a shaded spot, with the shower out of use. If in doubt, wait longer, as damp grout can stay dark after sealing. Let new grout fully cure first (see where the guides disagree, below).
- Test a patch and air the roomTry the sealer on a small hidden area first. Seal only at 10 degrees C or warmer. Keep the room well ventilated, put on the gear the label lists, and protect nearby surfaces if you are spraying.
- Seal a small section, wiping as you goRun a brush-on sealer along each joint, or spray evenly along the lines, for an even coat with no puddles, as too much may discolour some grout. Wipe any sealer off the tiles with a clean, dry cloth before it dries, or it can leave marks or a haze.
- Add a second coat, then test itMost sealers need more than one coat, so apply the next after the drying time on the label. Then put a few drops of water on the dry grout. If they bead on the surface, the seal is sufficient. If they soak in, add another coat.
- Keep it dry for at least 24 hoursKeep water, spills and dirt off the sealed grout for at least 24 hours, so leave the shower unused. Light foot traffic is usually fine after about 2 hours. Curing times vary by product, so check the label.
What you need to seal grout
Get these together before you start.
Clear penetrating grout sealer
A penetrating sealer soaks into the grout rather than sitting on top as a film. Check the label suits your grout and tiles, and buy enough for more than one coat.
Grout cleaner or mild detergent
A tile and grout cleaner, or water with a mild detergent, to lift the dirt first. For mouldy grout, add a product made for mould.
Stiff grout brush
A stiff-bristled brush to scrub dirt, stains and mildew out of the grout lines. A small brush or an old toothbrush works too.
Clean dry cloths
Plenty of clean, dry cotton or microfibre cloths, or paper towels, to wipe stray sealer off the tiles before it dries.
Brush-on or spray applicator
Brush-on sealer is more precise and suits small spaces. Spray suits large areas, but takes more preparation to keep overspray off nearby surfaces.
Protective gear from the label
The protective clothing, eye protection and dust mask or respirator that the label or safety data sheet lists for the product.
Staying safe when you seal grout
From Australian government pages, none of them about grout sealer by name.
Work in a well-ventilated room
SafeWork SA's page on adhesives and sealants, written for workplaces, says to use them in well-ventilated areas and avoid inhaling the vapours, as certain adhesives give off toxic vapours. Where good ventilation is not practicable, it says suitable breathing apparatus, such as respirators, should be worn.
Follow the label and safety data sheet
On the same page, SafeWork SA says to follow the instructions on both the Safety Data Sheet and the label, and to check the Safety Data Sheet for protective equipment. It says skin contact should be minimised, and goggles or face shields worn with runny adhesives to protect the eyes from splashes.
If you clean mould off first
On removing mould at home, the Better Health Channel says to make sure there is good ventilation and wear protective clothing, such as a shower cap, rubber gloves, eye protection, overalls, suitable footwear and a P1 or P2 face mask.
Before you repair old grout
The NSW Government's asbestos website says asbestos can be found in adhesives like grout, sealants, putties and dry powder mixes made before 1987. It advises having a licensed asbestos assessor check the property.
Sealing different grout and tiles
What changes with the grout and the tiles around it.
| Grout or tile | What to do |
|---|---|
| Cement grout | If you seal, use a penetrating sealer. Cement grout is porous, so in a shower water gets into it with every use. |
| Epoxy grout | It needs no sealer, as it does not soak up water, soap and stains the way cement grout does. |
| Glazed ceramic or porcelain tiles | The tiles rarely need sealing. If you seal the grout, wipe any sealer off the tile faces. |
| Natural stone | Stone tiles usually need sealing, with products that suit stone. Test a patch first, and keep vinegar and other acids off marble, travertine and limestone. |
Checked on 12 November 2026.
Where the guides disagree
Guides split on these points. Here is each side, with its caution.
How long to leave new grout
One sealer maker says new grout needs 24 hours to dry before sealing, and others say at least 72 hours. Another sealer maker says 28 days, warning that sealing earlier traps moisture inside the joint and weakens both the joint and the sealer's grip.
Vinegar before sealing
One sealing guide lifts stains with a 50/50 mix of vinegar and water. Another warns that acid cleaners can damage cement grout if left on too long. Acids, including vinegar, can also etch marble, travertine and limestone.
Do you need to seal at all?
Sealing guides favour it, as unsealed cement grout takes in water and stains. One cleaning business does not recommend it as standard: it says a sealer needs stripping before it can be redone, and adds a cost most homes do not need. Sealing the grout is your call.
Keeping sealed grout in good shape
How to make the sealer last, and when to seal again.
Clean it gently
Bleach, acid and solvent cleaners wear sealers down faster, so clean sealed grout with a pH-neutral cleaner.
Reseal when water soaks in
A clear sealer usually lasts 1 to 5 years, depending on the product, foot traffic and the cleaners you use. Repeat the water test now and then, and reseal when the drops soak in.
When to call a professional
Call a professional if any of these apply.
- The grout is cracked, crumbling or keeps going mouldySealer will not fix cracked or missing grout. Regrout if the grout is cracked, crumbling or missing, scrapes away with a fingernail, or grows mould again within days of a good clean.
- Old sealer, wax or a coating must come offA peeling film sealer has to be removed before new sealer can soak in. Stripping old wax or failed sealer is usually left out of a standard clean and quoted separately.
- Stains stay after a thorough cleanA colour seal is worked into the lines after a clean, giving every line one even colour and covering stains that will not lift. It can last 5 to 10 years or more.
A professional typically cleans with a hot water machine that sprays and vacuums at the same time, dries the floor, then seals it, and can offer a colour seal instead. As an estimate, a clear sealer typically adds about $2 to $12 a square metre to the clean. Home Ready Cleaning passes your job to one local cleaning business, and every business is insured.
Full details: Tile and grout cleaning
More on tile and grout cleaning
More how-to guides
Tile and grout cleaning
Tile and grout cleaning in the most searched places
About Home Ready Cleaning
Official sources
Checked on 13 November 2026.
- SafeWork SA, Adhesives and sealants
- Better Health Channel, Mould removal at home
- NSW Government asbestos website, Adhesives, dry powder mixes and asbestos
