Get my home cleaned
A clean grey tiled bathroom with a frameless glass shower screen and a timber vanity

How-to guide

Tile regrouting

Replace cracked, crumbling or missing grout in a shower or on a tiled floor yourself. Before you cut, check for hollow tiles, a leak and, in an older home, asbestos.

Updated 13 November 2026. Health and safety points come from thirteen government sources, listed at the end.

The short answer

Tap the tiles first: a hollow tile has to be re-bedded before you regrout. In a home built or renovated before 1990, have the grout checked for asbestos. Wearing a P2 mask and goggles, cut out the old grout, vacuum and wipe the joints, float in cement or epoxy grout diagonally and sponge off the haze. Keep it dry for 24 to 48 hours, and seal cement grout once it has fully cured.

What you need

  • P2 mask and goggles
  • Grout saw, rake or multi-tool
  • Vacuum and damp cloth
  • Cement or epoxy grout
  • Rubber float, bucket and sponge
  • Silicone and grout sealer
Step by step

How to regrout tiles, step by step

For a shower, wall or floor where the tiles themselves are sound.

  1. Tap the tiles and look for a leakTap each tile. One that sounds hollow has lost its bond and has to be lifted and re-bedded first, or new grout around it will crack. A ceiling stain below, a musty smell or water outside the shower can mean a leak that new grout will not fix.
  2. Put on a P2 mask and gogglesCutting out grout makes very fine dust. Wear what HealthyWA advises: a P2 rated mask fitted snugly over your mouth and nose, and goggles. Consider disposable overalls too, and take them off before going into the living areas. In a home built or renovated before 1990, read the asbestos advice below first.
  3. Cut out the old groutRun the grout saw, rake or multi-tool along each joint with steady pressure, taking care not to chip or scratch the tile edges. Get all the old grout out so the new grout has something solid to bond to. This is the slow part.
  4. Vacuum the dust and wipe the jointsVacuum as you go so you can see your progress, and do not dry sweep the dust. When the grout is out, wipe the tiles and joints with a damp cloth and let them dry before you regrout.
  5. Mix the grout to an even pasteFollow the maker's instructions and mix the grout in a clean bucket to an even paste that spreads easily but is not runny. Epoxy sets fast, so work quickly once it is mixed.
  6. Float it in diagonally across the tilesSweep the grout diagonally across the tiles with a rubber float, pressing firmly so it goes into the gaps. Keep going until every joint is full, with no air pockets.
  7. Sponge the haze off the tilesWring a damp sponge out well, as too much water can weaken the grout. Wipe across the tiles until each joint is clean and full and the haze is off the tile faces.
  8. Keep it dry, then seal cement groutKeep water and steam off the new grout for 24 to 48 hours. Once cement grout has fully cured, at least 72 hours after grouting, give it a penetrating sealer. Epoxy grout needs no sealer.
What you need

What you need to regrout tiles

Have these ready before you cut out any grout.

P2 mask and goggles

HealthyWA advises a P2 rated mask, fitted snugly over your mouth and nose, and goggles for renovation work that makes dust.

Grout saw, rake or multi-tool

A hand grout saw or rake is often enough for a small area. For a whole shower or room, or stubborn grout, a multi-tool with a diamond blade is faster.

Vacuum and damp cloth

A vacuum to clear dust from the joints as you work and to clean up after, and a damp cloth to wipe them clean.

Cement or epoxy grout

Cement grout suits walls and dry areas such as splashbacks, and epoxy suits shower floors and busy wet areas. The table below compares them.

Rubber float, bucket and sponge

A rubber grout float to press the grout in, a clean bucket to mix it in and a sponge to wipe off the haze.

Silicone and grout sealer

Flexible, mould-resistant silicone made for wet areas, for the corners and floor edge, and a penetrating sealer if you use cement grout. Epoxy needs no sealer.

Health and safety

Silica dust and asbestos in old grout

What government health and asbestos pages say about cutting out grout.

HealthyWA

Grout dust can contain silica

HealthyWA says silica in grout and tile is not a problem until it is cut or ground into very fine particles that can be breathed into your lungs. That fine silica can cause lung cancer and silicosis. Most cases come from repeated high exposure at work, it says, but home renovators still need to be cautious.

NSW Government

Old grout can contain asbestos

The NSW Government's asbestos website says asbestos can be found in adhesives like grout, and lists bathrooms, kitchens, laundries and floors for products made before 1987. You cannot tell by looking, it says, and a property built or renovated before 1990 probably has asbestos-containing materials.

HealthyWA

No power tools on possible asbestos

HealthyWA says you should never grind, sand or use power tools on material that might contain asbestos. If your house was built before 1990 and you are unsure, it says to check with an expert or treat the material you are working with as asbestos.

Cement or epoxy

Cement or epoxy grout

The grout you choose changes how you work and whether you seal it.

CompareCement groutEpoxy grout
Best forWalls and dry areas such as splashbacksShower floors and busy wet areas
Water and stainsPorous, so it soaks them upDoes not soak them up the way cement grout does
SealingNeeds a penetrating sealer in a shower, once fully curedDoes not need sealing
Applying itThe usual, lower-cost choiceCosts more, sets fast and takes more skill
Life in a showerUsually about 5 to 10 yearsOften 10 to 15 years or more

Checked on 12 November 2026.

What not to do

What not to do

Two mistakes to avoid once the new grout is in.

Grout in the corners

The corners and floor edge move a little, so they take silicone, not grout. Once the grout has set, cut out the old silicone and run in a flexible, mould-resistant wet-area silicone. Give it about 24 hours to cure, longer in humid weather.

Harsh cleaners on new grout

Keep bleach, acids and other harsh cleaners off the new grout for about 72 hours. After that, avoid them where you can, as harsh chemicals and bleach can erode grout over time.

Where guides differ

Where regrouting advice splits

On these two points the advice differs, and each side carries a caution.

How deep to cut

Regrouters cut the old grout out to the full depth of the joint, so the new grout has a solid base. A tiling guide warns that in wet areas you must take care not to damage the waterproofing membrane under the tiles, which new grout cannot repair.

Grouting over the old grout

A hardware forum post suggests simply grouting over the existing grout. The other guides and regrouters take the old grout out first, because new grout laid over old has nothing solid to bond to and tends to crack and lift within months.

Official sources

Checked on 13 November 2026.

  1. HealthyWA, Dust from DIY renovations
  2. NSW Government asbestos website, How do I know if it's asbestos?
  3. SafeWork NSW, Crystalline silica - general fact sheet
  4. NSW Government asbestos website, Adhesives, dry powder mixes and asbestos
  5. Building and Plumbing Commission, Waterproofing of wet areas
  6. Building Commission NSW, Waterproofing work
  7. Building and Plumbing Commission, Condensation, moisture damage and mould
  8. Queensland Building and Construction Commission, Industry Snapshot Top 10 defects: Home Owner series - Waterproofing
  9. SA.GOV.AU, Plumbing, gas fitting and electrical registration and contractors' licences
  10. Building and Energy (LGIRS), Plumbing work in your home
  11. Building Standards Tasmania, Plumbing for consumers
  12. City and Environment Directorate, Construction licences
  13. Northern Territory Government, Plumbing or drainage work on your property

Get a tile and grout cleaning quote