Get my home cleaned
A man pressure washing a mossy concrete driveway in front of a single storey brick home

How-to guide

Soft washing

Clean mould, algae and lichen off outside walls and eaves you can reach from the ground. Keep the pressure low: high pressure can strip paint, chip render and force water behind boards.

Updated 13 November 2026. Health and safety points come from seven government sources, listed at the end.

The short answer

Soft washing kills mould, algae and lichen on outside walls with a bleach-based solution and low pressure. Work from the ground. Test a hidden patch, close the windows, wet nearby plants and keep runoff out of drains. Mix to the label, spray in sections, never let it dry, then rinse it all off with clean water, top to bottom.

What you need

  • Chlorine bleach
  • Measuring container
  • Low-pressure sprayer
  • Garden hose
  • Gloves and eye protection
Step by step

How to soft wash a house, step by step

For walls and eaves you can reach from the ground.

  1. Work only where you can reach from the groundKeep to the walls and eaves you can wash safely from ground level. Leave high, damaged or hard-to-reach surfaces to a professional.
  2. Test the mix on a hidden patchOne mix does not suit every material, so work out what the wall is made of first. Then test a little of the mix on a small, hidden spot, as bleach can react with some paint colours.
  3. Close up the house and clear the wallsShut windows and doors. Move outdoor furniture and pot plants away from the walls, and bring in washing, shoes and doormats. Cover power points, lights and vents, and keep the spray off them.
  4. Wet the plants and plan the runoffWet garden beds, shrubs and lawn along the walls with clean water before any mix goes on, as bleach runoff can damage plants and soil. Plan where the runoff will go, and keep it out of stormwater drains.
  5. Measure the bleach mix to the labelMeasure the chlorine bleach and water to the dilution on the label for your surface. Read the bleach warning below before you add anything else to the mix.
  6. Spray it on in sections, out of strong sunSpray one section at a time at low pressure and leave it to work for a short time. Never let it dry on the wall: dried mix can damage the surface and leave streaks. Avoid hot sun and wind, which dry it too fast.
  7. Rinse it all off, top to bottomRinse with clean water at low pressure, from the top down, until no solution is left. Never turn the pressure up for a stubborn mark. Then rinse the garden beds, lawn and paths again with fresh water.
  8. Check it once dry before you go againLook the walls over after rinsing and again once dry. Streaks usually come from uneven spraying, the wrong dwell time or an incomplete rinse. Get advice before you repeat a treatment or make the mix stronger.
What you need

What you need to soft wash a house

Get these together before you start.

Chlorine bleach

Chlorine bleach (sodium hypochlorite) does the cleaning in a soft wash mix. Product strengths vary, so read the label for the dilution before you mix.

Measuring container

Something to measure with, so the mix is measured, not guessed. Too strong a mix can bleach surfaces, damage window seals and kill plants.

Low-pressure sprayer

A sprayer that puts the mix on at low pressure and suits the product. Never use a high-pressure wand on walls.

Garden hose

A garden hose and clean water, to wet the plants before you start and to rinse the walls and the garden afterwards.

Better Health Channel

Gloves and eye protection

Rubber gloves and eye protection. For mould removal at home, the Better Health Channel also lists overalls, suitable footwear, a shower cap and a P1 or P2 face mask.

Health and safety

Safety advice from government pages

Each point as an Australian government body puts it.

Better Health Channel

Never mix bleach with other cleaners

On its page about mould removal at home, the Victorian Department of Health's Better Health Channel says not to mix bleach with ammonia, acids or other cleaners, as this can release hazardous chlorine or chloramine fumes.

NSW Environment Protection Authority

Keep wash water out of drains

In its stormwater guidance for small industries and businesses, the NSW Environment Protection Authority says runoff from any washing must not enter stormwater drains. It says to store chemicals in closed, labelled containers and take old or unused ones to Community Recycling Centres.

Asbestos and Silica Safety and Eradication Agency

Fibro and asbestos cement

The Asbestos and Silica Safety and Eradication Agency says it is illegal in every state to use high pressure water spray or compressed air on asbestos materials. It says a home built before 1990 can contain asbestos inside and outside, and the only way to confirm it is to have a sample tested.

ACCC Product Safety

Think twice about a ladder

ACCC Product Safety says that on average more than 30 Australians, mainly men, die each year after falling from a ladder. It says to first consider whether you should use one, and not to work in wet or windy conditions or over-reach.

By surface

Soft washing render, weatherboards, brick, windows and roofs

What changes from one surface to the next.

SurfaceHow to wash it
Render and painted wallsLow pressure only. High pressure can drive water behind render, strip its texture coat and lift paint. Test painted walls first.
Weatherboards and claddingLow pressure, from the top down, so water is not driven up under the boards. Go gently around joins on fibre cement and metal.
Unpainted brickGuides differ. Some allow a little more pressure, kept back from the mortar. Another says pressure can damage brick: use low pressure and ideally get advice first.
WindowsGuides differ. One sprays the mix on with a 40 degree nozzle. Another keeps pressure off glass and uses pure water, as pressure risks the seals.
RoofsGuides differ on doing it yourself: one soft washes the roof from the ground, others leave roofs to professionals. The dead growth can take some weeks of rain to weather off.

Checked on 12 November 2026.

Where guides differ

Where the guides disagree

Guides split on these points. Here is each side, with its caution.

How strong to make the mix

One guide uses 1 part bleach to 3 parts water, another 30 parts 12.5% sodium hypochlorite to 70 parts water, less on delicate surfaces and more for heavy soiling. Others follow the label, as strengths vary. Three add a detergent so the mix clings: see the bleach warning above.

How long to leave it on

Times range from 5 to 10 minutes, or until the growth starts to fade, to 15 to 20 minutes or longer for heavy soiling. Cleaners often allow 10 to 15 minutes, and one guide follows the label. Each of these guides says not to let it dry.

What to spray it with

One guide turns a cold-water pressure washer down to about 500 to 600 PSI, with a 25 to 40 degree nozzle, once its manual says it suits bleach. Others use a soft wash pump at 200 to 500 PSI, a garden sprayer or about garden-hose pressure.

EPA South Australia

Where the runoff goes

For homes in South Australia, EPA South Australia says waste water from a high-pressure cleaner should go to a soakage area such as the garden or lawn, not the stormwater system. Soft washing guides warn that bleach runoff can damage plants, lawn and soil.

Official sources

Checked on 13 November 2026.

  1. Better Health Channel, Mould removal at home
  2. NSW Environment Protection Authority, Guidance for stormwater management: the drain is just for rain
  3. Asbestos and Silica Safety and Eradication Agency, The dangers of asbestos cement roofs
  4. Asbestos and Silica Safety and Eradication Agency, The home
  5. ACCC Product Safety, Ladders guide
  6. Environment Protection Authority South Australia, Around the home (stormwater management)
  7. Safe Work Australia, Safe work on roofs information sheet

Get a pressure cleaning quote